The sunn Forum

Other Musical Equipment => General Discussion => Topic started by: Walt-Dogg on August 26, 2011, 02:58:38 pm

Title: MIG100H Speaker Wiring
Post by: Walt-Dogg on August 26, 2011, 02:58:38 pm
My MIG100H has 3 speaker outputs, one 16 ohm, one 8 ohm, one 4 ohm. How do I get this to plug into a full stack of two 16 ohm or two 8 ohm cabs?
Title: Re: MIG100H Speaker Wiring
Post by: MammothVolume on August 26, 2011, 03:20:46 pm
Two 16 ohm cabs = 8 ohms, run it out of the 8 ohm jack.

Two 8 ohm cabs = 4 ohms, 4 ohm jack.

Cabs get paralleled, parallel down, series up. Parallel 2x16 = 8 ohms, Series 2x16 = 32
Title: Re: MIG100H Speaker Wiring
Post by: Walt-Dogg on August 26, 2011, 05:53:04 pm
So, can you parallel a Marshall 1960 4x12, the kind with the ohm selector switch on the back?
Title: Re: MIG100H Speaker Wiring
Post by: EdBass on August 26, 2011, 07:25:58 pm
Just run the Marshall mono, I think it's 8 ohms. You could parallel it with another 8 ohm cab to the 4 ohm tap.

If you mean can you run the cab stereo and parallel the two sides...
Well you could, but that would be a waste of cable and time; just run it mono off the 8 ohm tap.
Title: Re: MIG100H Speaker Wiring
Post by: MammothVolume on August 26, 2011, 11:42:45 pm
Not if it's the 16/4 ohm switchable Marshall. You can't daisy chain those.
Title: Re: MIG100H Speaker Wiring
Post by: EdBass on August 27, 2011, 08:11:39 am
On further research, I see the cab is 16 or 4 in mono, so obviously paralleling with another 8 ohm cab wouldn't work, so I'll change it;

Just run the Marshall mono, I think it's 8 ohms 16 or 4 ohms. You could parallel it with another 8 ohm 16 ohm cab to the 4 ohm 8 ohm tap.

If you mean can you run the cab stereo and parallel the two sides...
Well you could, but that would be a waste of cable and time; just run it mono off the 8 ohm 4 ohm or 16 ohm tap.

Would that work?
Title: Re: MIG100H Speaker Wiring
Post by: MammothVolume on August 27, 2011, 10:47:22 pm
I should go ahead and say NEVER use two of those jacks together. Not meant for that.

The 16/4 Marshalls aren't chainable. You COULD, in theory add a third jack back there paralleled from the 16 ohm (or 4 ohm)jack, so you could run it to a second 16 ohm (or 4 ohm) cab for a total load of 8 (or 2 which that amp won't do.)
Title: Re: MIG100H Speaker Wiring
Post by: Walt-Dogg on August 30, 2011, 10:10:22 pm
Oh well. I'm gonna invest in a pair of Orange or Avatar 4x12s soon that have parallel jacks so I can rig the MIG to two 4x12s no problem at 8 ohms and have a second 16 ohm cab to run with my Model T and 16 ohm Marshall 4x12 also at 8 ohms.
Title: Re: MIG100H Speaker Wiring
Post by: MammothVolume on August 30, 2011, 11:18:11 pm
We have a similar setup, buddy!

(http://a3.sphotos.ak.fbcdn.net/hphotos-ak-ash4/s720x720/302267_278310665519523_100000217744081_1277427_2768944_n.jpg)